I’ve tried all the “quick chill” methods I’ve heard of, but none of them work as quickly or as well as the icecream maker method. Watered down ice with some table salt. Set your unopened beer into a slurry like that, and in about 20 - 30 minutes, it’s surpremely cold. None of the “5 minutes and it’s ice cold” methods work as well or as quickly to be honest. At least not in my climate and in my experience.
There’s a cheap machine that dip the can in ice cold water and spin really fast. It cool the can down to <10°C in less than 10 minutes. I think it’ll work even better with your salt method.
By spinning the can in ice water, it increases the rate of transfer of heat energy from the drink in the can, to the can itself, to the ice water. It’s like how stirring the ice in a cup of not-cold water will melt the ice / cool the water faster.
At a molecular level, you would see an increase in the number of collisions between ice molecules and liquid molecules. The collisions must occur for heat transfer to happen, so more collisions = more cooling. It is also the same reason why a heatsink can draw more heat from a processor when a fan blows air over it (until the air is saturated with heat).
I’ve seen a video explain how it works, plus an explanation on how it doesn’t make carbonated beverage cans explode when opening like if you shaken it. But I can’t seem to find that video.
How can air get heat saturated? i followed you thus far but its not like humidity, you can always add more heat the question is if a faster flow decrease the time for each molecule to absorb the heat/motion and thats why sometimes higher flow wont yield in better cooling
Sorry, saturation is not the right word to describe it. I was thinking of the ice/water analogy and I mistakenly applied it to my heatsink analogy.
The correct limit to the heatsink analogy would a function of the thermal dissipation of the heatsink (material, surface area, thermal resistance) and the qualities of the surrounding fluid (ambient temp, flow, etc). Honestly, my comparison between the ice/water example and heatsinks is not good. It is only appropriate in reference to the “molecular collisions” concept I mentioned before.
The main reason spinning a can works is because it induces convection inside and outside of the can, which contributes to more collisions and better distributions of collisions. If the warmest soda is in the middle of the can, the cold molecules near the can walls will reach a temperature similar to the ice bath and thud the rate at which heat is transferred becomes stunted.
For lettuce, you’d have better luck finding a way to pass cold water between the leaves, much like having fins on a heatsink (surface area).
No, a lettuce spinner is a little basket inside of a container with a handle that you can spin to turn the basket. You wash your lettuce and put it into the basket and turn the handle. The centrifugal force (I think) causes the water clinging to the outside of the lettuce to drain into the container.
I think if you filled the container and basket partially up with ice or crushed ice) and some water, it’d achieve the same result as the machine someone linked above
Lol… I have never heard of this before. I think it would help halfway, but it won’t induce much stirring inside of the can, which is more important than just throwing more cold molecules of water at it.
I’ve tried all the “quick chill” methods I’ve heard of, but none of them work as quickly or as well as the icecream maker method. Watered down ice with some table salt. Set your unopened beer into a slurry like that, and in about 20 - 30 minutes, it’s surpremely cold. None of the “5 minutes and it’s ice cold” methods work as well or as quickly to be honest. At least not in my climate and in my experience.
There’s a cheap machine that dip the can in ice cold water and spin really fast. It cool the can down to <10°C in less than 10 minutes. I think it’ll work even better with your salt method.
How does that work?
Something like this
https://youtu.be/6WqZdMLkdCI
I think you can get it as cheap as $10-$15.
By spinning the can in ice water, it increases the rate of transfer of heat energy from the drink in the can, to the can itself, to the ice water. It’s like how stirring the ice in a cup of not-cold water will melt the ice / cool the water faster.
At a molecular level, you would see an increase in the number of collisions between ice molecules and liquid molecules. The collisions must occur for heat transfer to happen, so more collisions = more cooling. It is also the same reason why a heatsink can draw more heat from a processor when a fan blows air over it (until the air is saturated with heat).
Neat explanation, thanks.
I’ve seen a video explain how it works, plus an explanation on how it doesn’t make carbonated beverage cans explode when opening like if you shaken it. But I can’t seem to find that video.
How can air get heat saturated? i followed you thus far but its not like humidity, you can always add more heat the question is if a faster flow decrease the time for each molecule to absorb the heat/motion and thats why sometimes higher flow wont yield in better cooling
Sorry, saturation is not the right word to describe it. I was thinking of the ice/water analogy and I mistakenly applied it to my heatsink analogy.
The correct limit to the heatsink analogy would a function of the thermal dissipation of the heatsink (material, surface area, thermal resistance) and the qualities of the surrounding fluid (ambient temp, flow, etc). Honestly, my comparison between the ice/water example and heatsinks is not good. It is only appropriate in reference to the “molecular collisions” concept I mentioned before.
F me I forgot the beer in the freezer
When the temperature of the air and temperature of the object you want to cool reach an equilibrium, no heat gets transfered anymore.
Thanks for the answer! That’s pretty cool honestly. Could you achieve the same result with anything that spins, like a lettuce spinner?
The main reason spinning a can works is because it induces convection inside and outside of the can, which contributes to more collisions and better distributions of collisions. If the warmest soda is in the middle of the can, the cold molecules near the can walls will reach a temperature similar to the ice bath and thud the rate at which heat is transferred becomes stunted.
For lettuce, you’d have better luck finding a way to pass cold water between the leaves, much like having fins on a heatsink (surface area).
No, a lettuce spinner is a little basket inside of a container with a handle that you can spin to turn the basket. You wash your lettuce and put it into the basket and turn the handle. The centrifugal force (I think) causes the water clinging to the outside of the lettuce to drain into the container.
I think if you filled the container and basket partially up with ice or crushed ice) and some water, it’d achieve the same result as the machine someone linked above
Lol… I have never heard of this before. I think it would help halfway, but it won’t induce much stirring inside of the can, which is more important than just throwing more cold molecules of water at it.
You just need a way to spin the can. Probably works better if you speed it up and slow it down or reverse direction repeatedly.
I think a lettuce spinner would probably work, since it has a basket inside a container. I might give it a go next time I buy a can of anything