My current means of powering things is USB rechargable batteries. I have a about five of them that range between small 3000-5000mah ones to a big 20000mah interstate battery jump starter pack. Is there a device that lets me add all their power together into a centeral power source so I don’t have to keep swapping them out?

  • Zak@lemmy.world
    link
    fedilink
    arrow-up
    11
    arrow-down
    1
    ·
    1 year ago

    I’m assuming you mean USB powerbanks.

    I’d be surprised if there was such a device. It would require somewhat sophisticated electronics to work well, and the market for it would be small. A design that didn’t result in power cutting off during the switchover would need to keep at least two powerbanks active at a time, and that could negatively impact efficiency since the electronics in the powerbank consume power when active even under light loads.

    • testfactor@lemmy.world
      link
      fedilink
      arrow-up
      1
      arrow-down
      13
      ·
      1 year ago

      Or, I mean, it could just wire all the positives together and all the negatives together and hook that right into your target device.

      It’d be the same output voltage regardless. A little less internal resistance, and lower step down in the later phases, but neither should make a difference in what you’re powering.

      Kinda like how there were those converters for the GameBoy back in the day that let you put C batteries into it. Same principle.

      • Zak@lemmy.world
        link
        fedilink
        arrow-up
        16
        ·
        1 year ago

        It’s probably not possible to do that safely because USB power supplies aren’t just dumb batteries. They actively communicate with the device receiving power about how much current the device wants, and should only supply 500mA if they fail to do so.

        USB-A ports aren’t supposed to receive input power, which is effectively what would happen in that arrangement after a powerbank shuts off to prevent over-discharge of its batteries. The resulting behavior is, as I recall unspecified and might result in damage to the powerbank. Worse, it could interfere with the over-discharge protection and damage the batteries. Charging damaged Li-ion batteries is bad, where bad may include fire, explosion, and/or emission of toxic gas.

        • testfactor@lemmy.world
          link
          fedilink
          arrow-up
          4
          ·
          1 year ago

          Yeah, I should work on my reading comprehension.

          I deff read the prompt as having a bunch of rechargeable AA style Li-ion batteries, and how to utilize them without having to swap out to a new pair or whatever.

          Deff don’t want to do this with a bunch of disparately sized smart batteries providing power over USB. Very different problem.

        • thepianistfroggollum@lemmynsfw.com
          link
          fedilink
          English
          arrow-up
          1
          arrow-down
          2
          ·
          1 year ago

          You can still just crack open the banks and wire the cells together in parallel or series (depending on your needs), then hook them up to one of the controllers. I bet they’re just a bunch of 18650s

          • Zak@lemmy.world
            link
            fedilink
            arrow-up
            2
            ·
            1 year ago

            Sure, but you probably shouldn’t build a DIY battery pack out of salvaged 18650s of varying brands, capacities, and conditions unless you really know what you’re doing because that’s dangerous if you get it wrong.

      • Smokeydope@lemmy.worldOP
        link
        fedilink
        English
        arrow-up
        1
        arrow-down
        2
        ·
        1 year ago

        So I could actually get a couple of old short usb cords together cut the ends off, strip the positive and negative wires and hook them in series without it changing the output voltage?

        • sarchar@programming.dev
          link
          fedilink
          English
          arrow-up
          8
          ·
          1 year ago

          No…please do not do this.

          The voltages of the output ports are probably not all exactly the same and you could end up damaging the device (or worse, starting a fire). They MIGHT have reverse current protection on them, but I’ve seen some pretty sketchy power banks.

          You can’t just wire them in parallel. USB has communication pins that help boost circuits in the battery change voltages levels. Even if it all works, you’re going to get extremely poor charge times.

          I don’t believe it’s out of the realm of EE to design something that allows you to plug in multiple power banks though, but I’ve never seen any

    • Zak@lemmy.world
      link
      fedilink
      arrow-up
      8
      ·
      1 year ago

      That can work, but since the batteries are at roughly 3.0-4.2V depending on state of charge and standard USB power is 5V, that’s a whole lot of steps up and down. Each one takes an efficiency hit. The last one in a series of five would likely waste the majority of its energy.